BT/Siemens 1010 DECT Phone Codes -------------------------------- A/B/C = three keys across the top (STO, RCL, LNR) scode = system code (factory setting 0000) hpin = handset PIN (factory setting 0000) PWR (briefly) Handset keypad lock (=== appears) A # 1 C 0 3 Dial type: 3 - pulse, 7 - tone, short timed break, 8 - tone, long timed break, 6 - tone, earth recall, then A to store change C Recall last number, press up to 3 times to cycle through A 0 Speaker volume: 1 to 3, then A to store INT Put external call on hold. R to resume. A B 0-9 Review handset memories. Enter new number and A to store change. A 8 2 A Clear all handset memories. B 0-9 Recall handset memory. Press B repeatedly to cycle through. A # 1 C 9 6 Display call length: 0 - off, 1 - display minutes/seconds, 2 - display call cost or units, A to store A # 8 2 Enter cost per unit, A to store (if 0.00 entered, call units rather than cost is displayed) A # 8 3 Display total call cost/units: for handset 1-6, * for combined total, 0 to clear, then A to store. A # 8 * Change system code, enter new code twice then A to store. A 8 9 Change handset pin, enter new pin twice then A to store. A 5 Handset ringer volume: 1 to 6, then A to store. A 6 Handset ringer type: 1 to 6, then A to store. A # * 5 Base station ringer volume: 0 (off) to 6, then A to store. A # * 6 Base station ringer type: 1 to 6, then A to store. A 3 1 Key press beep: 0 - off, 1 - on, A to store. A 3 4 Warning tone: 0 - off, 1 - on, A to store. A 3 7 Confirmation tone: 0 - off, 1 - on, A to store. A 3 2 Low battery warning tone: 0 - off, 1 - on, A to store. A 3 3 Out of range warning tone: 0 - off, 1 - on, A to store. A 3 5 Entering range tone: 0 - off, 1 - on, A to store. A 3 8 Answer call by picking up handset: 0 - off, 1 - on, A to store. A # 2 4 Lock all outgoing calls: 0 - off, 1 - on, A to store. A # 2 5 Enter up to 4 emergency numbers (not locked), C to cycle. A # 2 7 Clear all emergency numbers. A 8 8 Enter direct dial number for handset: C to enter new number, then A to store. A 8 1 A Lock handset (can only dial direct number). A 8 0 A Unlock handset. A # 8 5 Enter prohibited numbers for individual handsets. 1 to 6 (handset number), then C to review/enter prohibited prefixes. A # 8 7 Reset prohibited numbers for selected handset 1 to 6, A to confirm. A # 8 4 Enable prohibition of numbers for selected handset 1 to 6, 0 - unlock, 1 - lock, A to store. INT 1-6 Call another handset (or * to page all), then hang up to transfer an external call, or press R to reconnect. Register handset: Turn off handset, press and hold base station page button till it beeps, press and hold 1 (or 2 to 4 for other base stations) on handset as you turn handset on, enter system code and #, then enter extension number 2 to 6 for handset. A # 1 C * 1 Disable outgoing calls for handset 1 to 6: 1 - enable, 0 - disable (lock), A to store. A # 1 C * 2 3 Group or priority pickup of incoming calls: 1 - collective (group) pickup, 2 - priority pickup A # 1 C * 2 1 Add or remove handsets from group pickup. A # 1 C * 2 2 Enter priority handset 1 to 6 (first to receive incoming calls). A # 1 C * 6 Enter number of rings (2 to 9) after which incoming calls switch from priority to collective group pickup. A # 7 2 Unregister handset 1 to 6 from base station. A # 0 C Enter exchange access code(s), C to cycle through A # 1 C 0 2 Enter exchange access pause interval: 0 (3 secs), 1 (6 secs), 4 (1 second), 0 (2 secs), A to store. A # 1 C 2 5 3 Clear exchange access codes, A to confirm. A 3 6 Enable display of current base station, 0 - off, 1 - on, A to store. A INT Select base station: 0 - search for strongest, 1 to 4 - manually select base station. A 8 B A Restore handset to factory settings. A # 1 C 2 5 0 Restore base station to factory settings, A to store. A 3 9 Enable switching from pulse to tone dialling during call with *: 1 - on, 0 - off, A to store. A 1 ? A # 1 C 4 ? A # 1 C # ?